Product support

Alia Bollente boiling unit setup, care and support

How the Bollente boiling unit under your sink is installed, how to set its temperature, look after it and fix common problems.

Alia Bollente boiling unit with boiling outlet, water inlet and touch display labelled

About your Bollente

What it does

The Bollente is the boiling unit under your sink. It heats filtered water and holds it ready for your X51 or 4 in 1 tap.

It's open vented, so the tank isn't under pressure. That's why there's a short pause before boiling water flows from the tap.

Which systems use it

Every Alia boiling tap uses the Bollente, the X51 and the 4 in 1.

Setup

Step 1. Place it

Stand the Bollente upright and level, close to the tap. Leave 50–100mm of air at each side and about 25mm at the back. Keep the display at the front, where you can reach it.

Step 2. Connect the water

The inlet and the outlet are both 3/8" BSP male threads. The blue inlet takes filtered water in. The red outlet sends boiling water up to the tap.

It works between 150 and 500 kPa. If your mains pressure is above 500 kPa, the manual asks for a pressure reducing valve on the cold mains inlet.

Only connect it to mains water that is safe to drink. Don't connect it to rainwater from a tank, or to water that is microbiologically unsafe.

Step 3. Fill it before power

Fill the tank from the tap until water flows steadily, then check every connection point. Only then plug it in and switch it on.

If it's switched on empty, it shows E3 and won't heat. That protects it.

Using the display

Your Bollente display

The round display on the front shows two temperatures. The top number, SET, is the temperature you chose. The bottom number, ACT, is the water temperature in the tank right now.

The power button is at the bottom, OK on the left and SET on the right.

Set the temperature

Set the temperature

  1. Hold the power button for 3 to 4 seconds. The display lights up.
  2. Touch SET to step through the seven settings, 35, 55, 85, 95, 96, 97 and 98°C.
  3. Touch OK to confirm. The Bollente starts heating.

It's set to 98°C by default. If the water seems to boil all the time, lower the setting to 95°C.

While it heats

While it heats

A red arc of lights moves while it heats, and stays still once the water reaches your setting. After you pour, it reheats by itself.

Care

After a few days away

If it hasn't been used for more than 2 days, pour off the boiling water, let it reheat and repeat 2 or 3 times.

Going away for longer? Switch it off at its power button.

Check for leaks now and then

Look at the hoses and connection points from time to time. Replace any loose or split hose straight away. For extra protection, your plumber can stand the Bollente in a drain tray connected to a drain.

Freezing weather

The Bollente must never freeze. If it could, ask your plumber to drain it.

  1. Turn off the mains water and unplug the Bollente. Let it cool for at least an hour.
  2. Disconnect the inlet and remove the silicone outlet hose.
  3. Lift it to the sink, turn it upside down and drain all the water.
  4. To use it again, reinstall it following the setup steps.

Troubleshooting

E3The display shows E3

The tank is empty, so the heater won't switch on. Switch the Bollente off at its power button, fill it from the tap until water flows steadily, then switch it on again.

If you leave it, it switches itself off after about 5 minutes until it's filled.

The water isn't hot

Check it's plugged in, its powerpoint is on and the display is lit. If the display stays dark, check the safety switch in your switchboard. Then press the power button for 4 seconds to switch it on, choose a temperature with SET and confirm with OK.

Water and steam spit from the spout

The water is boiling. Pour a little off and lower the setting by 1–2°C. Check the aerator at the end of the spout isn't blocked.

The spout drips after I pour

Very small pours can leave water in the expansion chamber. Pour about 200mL, around one cup, to clear it, and avoid pours under 100mL, a little under half a cup.

Specifications

Bollente at a glance

PartDetail
Size195mm wide, 200mm deep, 295mm high
Tank2.4 L, up to 1.6 L in one pour
Power1600 W, its own earthed powerpoint
TemperatureSeven settings, 35, 55, 85, 95, 96, 97 and 98°C, set to 98°C by default
WaterOpen vented, 100 kPa standing, works between 150 and 500 kPa
Connections3/8" BSP male, inlet and outlet

Warranty and help

Your warranty

Your Bollente is covered by Alia's 2-year warranty. Keep your proof of purchase.

Don't open, modify or repair the unit yourself. It's unsafe and it voids your warranty. Read the full warranty policy.

Talk to our team

Call (03) 9219 0189 or email sales@aliaglobal.com.au. Tell us your model and any code on the display, and have your proof of purchase handy. A photo of the setup under your sink helps us help you.

Downloads

Still need help?

Call or email our team. Have your model and proof of purchase handy.