Product support

Alia AG-ST1000 Smart Toilet troubleshooting and support

Quick fixes for common problems, what each fault code means and how to reach our team.

Alia smart toilet diagram with parts labelled

Start here

Common problems

Nothing works

Check the powerpoint is on. If the earth leakage switch on the plug has tripped, press it to reset it.

In a power cut, wait for the power to come back. You can still flush with the side knob if the spare battery box is fitted.

The knob light flashes every 5 seconds and nothing runs

The toilet is in standby. Hold the side knob for 5 seconds to wake it.

The rear wash doesn't start

Check the angle valve is open and your water is on. Sit so your skin touches the seat sensor.

If the nozzle holes are blocked, clean the nozzle by hand. Hold Stop and Rear Wash for 3 seconds and wipe it with a soft cloth.

The wash pressure is low

Turn the water pressure up with + on the remote. If it's still low, the filter screen at the water inlet may need cleaning. Ask your plumber to clean it.

The wash water isn't warm enough

Turn the water temperature up on the remote. There are six levels, and the lowest one turns the heating off.

The wash stops partway

Each wash stops by itself after a set time, so start it again. It also stops if you move off the seat sensor.

The dryer isn't warm, or it stops

Turn the air temperature up on the remote. The dryer stops by itself after a set time, or if you move off the seat sensor. Start it again.

The seat isn't warm enough

Turn the seat temperature up on the remote. After a long sitting, the seat drops to its lowest level on purpose, to prevent low-temperature burns.

The deodoriser doesn't run

It only runs while you're seated, with skin on the seat sensor. Adjust how you're sitting.

The remote doesn't respond

Clear anything in front of the toilet's sensor window and point the remote at the toilet from closer.

If the red light on the remote flashes, fit two new AAA alkaline batteries. Still nothing? Pair the remote again. The steps are on the setup and installation page.

How do I turn the beeps off?

Hold Stop and Dryer on the remote for 3 seconds to turn mute mode on. Do the same to turn it off.

Fault codes

Toilet and controls

CodePartWhat it meansWhat happensWhat to do
EEWhole toiletSeveral sensors have failedThe toilet stops workingCall us if it doesn't clear
E1Wash water heaterIts signal isn't getting throughHeating and washing stopClears when the signal returns. Call us if it stays
E2Water flowWater keeps running after a wash endsThe rear or front wash won't stopClose the angle valve and call us
E3Water inletNo flow after the inlet valve opensThe water stops heating. Other functions still workCheck the angle valve is open and your water is on
E4Lid and seat motorThe gearbox is stuckThe lid and seat stop opening and closingCheck nothing is blocking them. Call us if it stays
E5Side knobNo response when turned anticlockwiseThe knob lights flash in turnClears when the knob responds. Call us if it stays
E6Side knobNo response when turned clockwiseThe knob lights flash in turnClears when the knob responds. Call us if it stays
E7Side knobNo response when pressedThe knob lights flash in turnClears when the knob responds. Call us if it stays

Wash water temperature

The water temperature light flashes.

CodePartWhat it meansWhat happensWhat to do
A1Inlet sensorThe incoming water sensor has a faultHeating and washing stopClears when the sensor recovers. Call us if it stays
A2Inlet sensorThe incoming water is above 42°CHeating and washing stopCheck the toilet is on the cold water supply, not the hot
A3Outlet sensorThe wash water sensor has a faultHeating and washing stopClears when the sensor recovers. Call us if it stays
A4Outlet sensorThe wash water is above 42°CHeating and washing stopClears once the water cools
A5Inlet sensorThe water isn't warming upHeating and washing stopCall us if it doesn't clear

Dryer

The air temperature light flashes.

CodePartWhat it meansWhat happensWhat to do
C1Air sensorThe air temperature sensor has a faultThe dryer stops heatingClears when the sensor recovers. Call us if it stays
C2Air sensorThe air is above 65°CThe dryer stops heatingClears once the air cools
C3Air sensorThe air isn't warming upThe dryer stops heatingCall us if it doesn't clear

Heated seat

The seat temperature light flashes.

CodePartWhat it meansWhat happensWhat to do
H1Seat sensorThe seat sensor has a faultSeat heating stopsClears when the sensor recovers. Call us if it stays
H2Seat sensorThe seat is above 42°CSeat heating stopsClears once the seat cools

Warranty and help

Your warranty

Every Alia product is covered by a 2-year warranty. Keep your proof of purchase.

Alia doesn't have authorised installers for the smart toilet. For questions about the installation, talk to your licensed plumber.

Read the full warranty policy.

Downloads

Still need help?

Call or email our team. Have your model and proof of purchase handy.