Product support

Alia X51 Boiling, Chilled and Sparkling operation and maintenance

How to pour each water, set the temperature and keep your Alia X51 Boiling, Chilled and Sparkling in good order.

Alia X51 boiling, chilled and sparkling tap system diagram showing the tap, filter and under-sink units

Using your tap

Your X51 touch panel

The touch panel on the front of the tap pours your filtered water. The lever on the side gives your everyday hot and cold water.

Pour boiling water

Boiling water

  1. Hold the padlock for 2 seconds, then let go. This unlocks boiling water.
  2. Before it locks again, press and hold the red boiling button.
  3. Let go to stop. The tap locks again by itself.

A short pause before the water flows is normal. The Bollente isn't under pressure, so water takes a moment to start.

Pour chilled and sparkling water

Chilled water

Press the chilled button once to start the water, and press it again to stop. It pours at 8–12°C in normal use.

Sparkling water

Press the sparkling button once to start the water, and press it again to stop. Your sparkling water comes out chilled.

Hot and cold water

Hot and cold water

Lift the mixer lever and turn it towards hot or cold. This is your everyday hot and cold water. It isn't filtered.

Under-sink settings

Boiling temperature

The Bollente display

  1. Hold the power button for 3 to 4 seconds. The display lights up.
  2. Touch SET to step through the seven settings, 35, 55, 85, 95, 96, 97 and 98°C.
  3. Touch OK to confirm. The Bollente starts heating.

The top number, SET, is the temperature you chose. The bottom number, ACT, is the water temperature in the tank right now. A red arc moves while it heats and stays still once it's at temperature.

It's set to 98°C by default. If the water seems to boil all the time, lower the setting to 95°C.

Chilled and sparkling

The Fizz-X panel

Touch the temperature button to set how cold your water pours, and touch on/off to start or stop the Fizz-X. Don't change the setting while it's cooling. Wait until it settles.

The power switch and the water, chilled, sparkling and CO₂ connections are at the back.

Set the fizz

The regulator on top of the CO₂ cylinder sets how much CO₂ reaches the Fizz-X. Your plumber sets it so the right-hand gauge reads 4 bar, the red line. Turn the knob to choose a lighter or a stronger fizz.

The left-hand gauge shows how much CO₂ is left in the cylinder. When its needle reaches the red zone, it's time for a new cylinder.

Care and maintenance

Change the filter

Change the filter every 8–12 months

The F5000L filters every glass of boiling, chilled and sparkling water. Change it every 8–12 months. Once it's wet, the activated carbon inside ages, so time decides the change, not how much you pour.

  1. Turn off the cold water stop valve.
  2. Open the filtered water at the tap to release the pressure. No water will flow.
  3. Hold the old cartridge firmly and unscrew it from the filter head, then dispose of it.
  4. Screw the new cartridge in until it stops turning.
  5. Turn the stop valve back on slowly. Air, then water, will come out of the tap.
  6. Run off the first 5 litres (about half a bucket), check for leaks, then write the install date on the label.

Need a new cartridge? Order the F5000L. It's $150, including GST and delivery.

Change the CO₂ cylinder

Swap the CO₂ cylinder

In a typical home, one cylinder lasts around 6–8 months. When the fizz starts to fade, it's time for a new one.

  1. Read the CO₂ safety data sheet before you fit your first cylinder.
  2. Work in a well-ventilated spot, away from heat and flames.
  3. Take the protection cap off the new cylinder's valve.
  4. Connect the approved pressure regulator to the valve.
  5. Set the regulator back to 4 bar, the red line, or to the fizz you like.
  6. Handle the cylinder with care. Never drop, pierce or burn it, even when it's empty.

Order a CO₂ cylinder. It only fits the Alia Fizz-X, and it must never be refilled.

Everyday care

After a few days away

If the system hasn't been used for more than two days, pour off the boiling water, let it reheat and repeat two or three times. Run filtered water for 30 seconds before you drink it.

Going away for longer? Switch the Bollente off at its power button. If the Fizz-X won't be used for more than a week, drain its tank with the drain plug at the bottom.

Look after the under-sink units

  • Check the hoses and connection points under the sink now and then for leaks. Replace any loose or split hose straight away.
  • Keep the vents on every unit clear, and don't put anything on top of them.
  • Never wash a unit with water.
  • For extra protection, the Bollente can sit in a drain tray connected to a drain. Your plumber can fit one.

Power and plugs

  • Never touch a plug or a powerpoint with wet hands.
  • To unplug a unit, pull the plug itself, never the cord.
  • If a power cord is damaged, don't use the unit. A qualified technician must replace the cord. Call us to arrange it.

Freezing weather

The system must never freeze, and freeze damage isn't covered by the warranty. If your kitchen could freeze, ask your plumber to drain it.

  1. Turn off the mains water and unplug the Bollente. Let the tank cool for at least an hour.
  2. Disconnect the inlet to the tank and remove the silicone outlet hose.
  3. Lift the Bollente to the sink, turn it upside down and drain all the water.
  4. To use it again, reinstall it following the setup steps.

Still need help?

Call or email our team. Have your model and proof of purchase handy.