Product support

Alia X51 Boiling and Chilled operation and maintenance

How to pour each water, set the temperature and keep your Alia X51 Boiling and Chilled in good order.

Alia X51 boiling and chilled tap system diagram showing the tap, filter and under-sink units

Using your tap

Your X51 touch panel

The touch panel on the front of the tap pours your filtered water. The lever on the side gives your everyday hot and cold water.

Pour boiling water

Boiling water

  1. Hold the padlock for 2 seconds, then let go. This unlocks boiling water.
  2. Before it locks again, press and hold the red boiling button.
  3. Let go to stop. The tap locks again by itself.

A short pause before the water flows is normal. The Bollente isn't under pressure, so water takes a moment to start.

Pour chilled water

Chilled water

Press the chilled button once to start the water, and press it again to stop. It pours at 8–12°C in normal use.

Hot and cold water

Hot and cold water

Lift the mixer lever and turn it towards hot or cold. This is your everyday hot and cold water. It isn't filtered.

Under-sink settings

Boiling temperature

The Bollente display

  1. Hold the power button for 3 to 4 seconds. The display lights up.
  2. Touch SET to step through the seven settings, 35, 55, 85, 95, 96, 97 and 98°C.
  3. Touch OK to confirm. The Bollente starts heating.

The top number, SET, is the temperature you chose. The bottom number, ACT, is the water temperature in the tank right now. A red arc moves while it heats and stays still once it's at temperature.

It's set to 98°C by default. If the water seems to boil all the time, lower the setting to 95°C.

Chilled water

Chilled Stream temperature

  1. Hold the snowflake button for 5 seconds.
  2. Keep pressing it to step through the settings.
  3. Press the power button once to confirm.

Don't change the setting while the Chilled Stream is cooling. Wait until it settles.

Care and maintenance

Change the filter

Change the filter every 8–12 months

The F5000L filters every glass of boiling and chilled water. Change it every 8–12 months. Once it's wet, the activated carbon inside ages, so time decides the change, not how much you pour.

  1. Turn off the cold water stop valve.
  2. Open the filtered water at the tap to release the pressure. No water will flow.
  3. Hold the old cartridge firmly and unscrew it from the filter head, then dispose of it.
  4. Screw the new cartridge in until it stops turning.
  5. Turn the stop valve back on slowly. Air, then water, will come out of the tap.
  6. Run off the first 5 litres (about half a bucket), check for leaks, then write the install date on the label.

Need a new cartridge? Order the F5000L. It's $150, including GST and delivery.

Everyday care

After a few days away

If the system hasn't been used for more than two days, pour off the boiling water, let it reheat and repeat two or three times. Run filtered water for 30 seconds before you drink it.

Going away for longer? Switch the Bollente off at its power button.

Look after the under-sink units

  • Check the hoses and connection points under the sink now and then for leaks. Replace any loose or split hose straight away.
  • Keep the vents on every unit clear, and don't put anything on top of them.
  • Never wash a unit with water.
  • For extra protection, the Bollente can sit in a drain tray connected to a drain. Your plumber can fit one.

Power and plugs

  • Never touch a plug or a powerpoint with wet hands.
  • To unplug a unit, pull the plug itself, never the cord.
  • If a power cord is damaged, don't use the unit. A qualified technician must replace the cord. Call us to arrange it.
  • After a power cut, unplug the Chilled Stream and wait 5 minutes before you plug it back in.

Freezing weather

The system must never freeze, and freeze damage isn't covered by the warranty. If your kitchen could freeze, ask your plumber to drain it.

  1. Turn off the mains water and unplug the Bollente. Let the tank cool for at least an hour.
  2. Disconnect the inlet to the tank and remove the silicone outlet hose.
  3. Lift the Bollente to the sink, turn it upside down and drain all the water.
  4. To use it again, reinstall it following the setup steps.

Still need help?

Call or email our team. Have your model and proof of purchase handy.