Product support

Alia X51 Chilled Upgrade Kit setup and support

How your licensed plumber adds the Chilled Stream to your X51 Boiling and Ambient tap. What changes at the tap, and where to get help.

Chilled Stream under-sink unit for the Alia X51 boiling and chilled tap with air vents labelled

About the kit

What the kit does

The kit adds chilled water to an Alia X51 Boiling and Ambient tap that is already installed. A chilling unit, the Chilled Stream, goes in the cabinet beside your Bollente.

Your tap, its finish and your benchtop stay as they are. Once the kit is fitted, your system matches the Alia X51 Boiling and Chilled.

What comes in the kit

  • Chilled Stream chilling unit, with its power cord
  • New tubes and fittings to connect it

Your X51 tap, X51 control box, Bollente and F5000L filter stay in place.

Which tap it fits

Only the Alia X51 Boiling and Ambient tap. On your invoice, its model code starts with AG-BX.

Have an Alia 4 in 1 Boiling and Ambient tap? See the Alia 4 in 1 Chilled Upgrade Kit guide.

Before your plumber starts

Cabinet space

The upgraded system fits a clear space 500mm wide, 580mm deep and 450mm high inside the cabinet. That is the space your system needs today.

The Chilled Stream is 140mm wide, 350mm deep and 310mm high. It stands beside the Bollente and needs space around it for air.

Power

The upgraded system needs three powerpoints under the sink, one each for the X51 control box, the Bollente and the Chilled Stream. That is one more than you have now.

The Chilled Stream plugs into its own earthed, switched powerpoint. Don't use a double adaptor or an extension lead.

If there is no spare powerpoint, a licensed electrician must fit one before installation day.

Fitting the kit

Your system after the upgrade

This is how the system sits in the cabinet once the kit is in. The Chilled Stream is the new part. Everything else is already under your sink.

Step 1. Place the Chilled Stream

Stand the Chilled Stream level, with space around it for air. It gives off heat, so the cabinet needs a vent. Without one, its manual asks you to keep the cabinet door open while it runs. A large cabinet with plenty of space around the Chilled Stream doesn't need a vent.

Take the blue clips and covers off Water In and Water Out. Water In comes from the filter. Water Out goes to the X51 control box.

Step 2. Connect the chilled line

On your system today, one line runs from the filter outlet to IN on the control box.

From the filter outlet, fit a T-piece. Run one line to IN on the control box and one to Water In on the Chilled Stream.

Run the chilled line from Water Out on the Chilled Stream to the control box. Follow the arrows on the back of the control box, which show which way the water flows.

Use the new tubes supplied, never old ones. Push each tube in all the way and refit every clip.

Step 3. Check for leaks before power

Check every clip is in and the cabinet is dry. Turn the water back on and check every connection point.

Step 4. Fill and flush the chilled line

Plug the X51 control box back in and switch it on. Run water from the blue button until it flows steadily, so the Chilled Stream tank is full. If the panel doesn't respond, unlock it first.

Plug in the Chilled Stream and switch it on. Run chilled water for five minutes to flush it, and don't drink it until it's flushed. Within 15 minutes the water should start to get colder.

Step 5. Switch the Bollente back on

Plug the Bollente back in and switch on its powerpoint. Check its display is lit.

If the display is dark, hold the power button for 3 to 4 seconds. Choose a temperature with SET and confirm with OK.

Step 6. Final check and handover

With everything running, check every connection point once more.

Show the household that the blue button now pours chilled water.

After the upgrade

What changes, and what stays the same

What changesBeforeAfter
Boiling water35–98°C, filteredNo change
Blue button on the panelFiltered ambient waterChilled water, 8–12°C
Mixer leverHot and cold water from the mainsNo change
Under the sinkX51 control box, Bollente and filterX51 control box, Bollente, Chilled Stream and filter
PowerpointsTwoThree

Pour chilled water

Use the blue button. Before the upgrade it poured filtered ambient water. Now it pours chilled water in its place, at 8–12°C.

Boiling water and the mixer lever work as they did before.

Can I add sparkling water later?

Yes, but not with a kit. The Chilled Stream is removed and a Fizz-X takes its place, because the Fizz-X chills as well as carbonates.

Call us on (03) 9219 0189 to arrange it.

Troubleshooting

The chilled water isn't cold yet

After you switch it on, the chilled water should start getting colder within 15 minutes. Give it time after heavy use.

Check the Chilled Stream has air around it and its vents are clear.

If it stays slow to cool, move it out of direct sun and away from heat, such as an oven or dishwasher. If the cabinet is small, check it has a vent.

The Chilled Stream doesn't turn on

Check its plug is in and its powerpoint is switched on. Check the cord isn't damaged. If the cord is damaged, don't use the unit and call us.

E1The Chilled Stream shows E1

E1 means the temperature probe needs checking. Switch the Chilled Stream off and call us on (03) 9219 0189. Don't open the unit.

There's water under the sink

Turn off the stop taps and switch off each unit at its powerpoint. Dry the area and look for the wet connection point.

Call your plumber to fix it, and call us on (03) 9219 0189 if a part needs replacing.

Warranty and help

Your warranty

Your kit is covered by Alia's 2-year warranty, like every Alia product. Keep your proof of purchase.

Don't open, modify or repair a unit yourself. It's unsafe and it voids your warranty. Read the full warranty policy.

Downloads

Still need help?

Call or email our team. Have your model and proof of purchase handy.